u/Azelphur

Hi folks.

I'm really struggling to pick a camera, atm I have 9 cameras, they are all old analogue dome cameras. One of them has died so I need to replace it. The good news is the original installer used ethernet cable and is just shunting the analogue signal and 12V down it. So I can unplug it, put RJ45's on the end, and use PoE. Yay.

• Must be PoE of course
• Is to be used with Frigate
• My house is set back from the street, but I also have neighbours, so cameras that require the flood lights to run at night are probably a no-go? But perhaps cameras that have IR night vision and can switch to white light / color night vision when an object is detected could be good?
• The camera that has died is covering a driveway, 25 meters long. It's mounted up high on the house
• The existing cameras are all turret cameras, but I'm not opposed to changing that if there are benefits to doing so
• I don't think I need features like PTZ or Zoom
• Must be purchasable in the UK, ideally from Amazon but that's optional.
• My budget is up to £200

Feel free to ask questions if I've missed anything above, hopefully someone can steer me in the right direction. Thanks :)

Hi folks.

Occasionally (and annoyingly today, after 30 hours of print time...), I get:

Lost communication with MCU 'EBB'
Once the underlying issue is corrected, use the
"FIRMWARE_RESTART" command to reset the firmware, reload the
config, and restart the host software.
Printer is shutdown

dmesg says:

[2399002.791744] usb 3-2-port2: disabled by hub (EMI?), re-enabling...
[2399002.791756] usb 3-2.2: USB disconnect, device number 10
[2399003.687533] cdc_acm 3-2.2:1.1: acm_start_wb - usb_submit_urb(write bulk) failed: -19
[2399003.712801] cdc_acm 3-2.2:1.1: acm_start_wb - usb_submit_urb(write bulk) failed: -19
[2399003.762957] cdc_acm 3-2.2:1.1: acm_start_wb - usb_submit_urb(write bulk) failed: -19
[2399003.863180] cdc_acm 3-2.2:1.1: acm_start_wb - usb_submit_urb(write bulk) failed: -19
[2399004.063510] cdc_acm 3-2.2:1.1: acm_start_wb - usb_submit_urb(write bulk) failed: -19
[2399004.464018] cdc_acm 3-2.2:1.1: acm_start_wb - usb_submit_urb(write bulk) failed: -19
[2399004.671694] cdc_acm 3-2.2:1.1: acm_start_wb - usb_submit_urb(write bulk) failed: -19
[2399005.265442] cdc_acm 3-2.2:1.1: acm_start_wb - usb_submit_urb(write bulk) failed: -19
[2399005.655937] cdc_acm 3-2.2:1.1: acm_start_wb - usb_submit_urb(write bulk) failed: -19
[2399006.639999] cdc_acm 3-2.2:1.1: acm_start_wb - usb_submit_urb(write bulk) failed: -19
[2399006.866379] cdc_acm 3-2.2:1.1: acm_start_wb - usb_submit_urb(write bulk) failed: -19
[2399007.624065] cdc_acm 3-2.2:1.1: acm_start_wb - usb_submit_urb(write bulk) failed: -19
[2399007.815059] xhci-hcd xhci-hcd.1: xHCI host not responding to stop endpoint command
[2399007.835231] xhci-hcd xhci-hcd.1: xHCI host controller not responding, assume dead
[2399007.835257] xhci-hcd xhci-hcd.1: HC died; cleaning up
[2399007.835862] usb 3-1: USB disconnect, device number 2
[2399007.887322] usb 3-2: USB disconnect, device number 3
[2399007.887329] usb 3-2.4: USB disconnect, device number 11

My first guess is that the cable has worn out. Is there any way to source a new cable without buying the whole kit, or does anyone have any suggestions on what may be causing the problem?