▲ 13 r/SCX24
3D printed course
hey I wanted to share this 3D printed course I designed. these are 9x9 inch tiles and can snap together in any arrangement so you can constantly change it up whenever you feel.
u/TECwatches — 3 hours ago
r/SCX24
▲ 2 r/SCX24
Loving my first build!
I missed my old Scx24 and decided to build one from the ground up! It is such an awesome build, I can’t wait to build a course for it
u/Far-Accident6717 — 30 minutes ago
▲ 1 r/SCX24
New “crossing” created
It’s too cold to install but should be warm enough on Friday, we’ll see.
Wanted to build a crossing into the new area under development and wanted something a little different so I built a pipe crossing. We’ll see how it installs, I’m sure it will look better once it’s in place.
Happy crawling everyone.
u/RollingSwede — 38 minutes ago
▲ 9 r/SCX24
This whole project has been a learning experience.
Had some extra frame rails, and found an I beam kit on Etsy. This has been a process but it’s slowly coming together.
u/toyo1937 — 8 hours ago
▲ 12 r/SCX24
How low can we go?
I will find 10g somewhere to get this one below 350g with the body and goofballs in the interior!
u/Familiar_Palpitation — 11 hours ago
▲ 14 r/SCX24
My Trail Blazer Build 🫡😎
Got the Trail Blazers out on my at home rock course. Out here flexing on it 😎🫡
.
.
.
.
.
.
.
.
.
#scx24 #rctrucks #rccrawling #rc #crawlers
u/RC24_GREY — 15 hours ago
▲ 16 r/SCX24
Slowly but surely.
Piece by piece till I have a mini 4Runner🫣
u/PNW_4RUNNER — 19 hours ago
▲ 12 r/SCX24
Attempting to make a copy of my 4Runner!
Lmk what u guys think so far and some tips I could use!
u/PNW_4RUNNER — 20 hours ago
▲ 9 r/SCX24
Backyard crawler course
Most of the stones I got from pillaging my local church parking lot. With nothing but a plastic fold out cart that was way too short to walk long distances with. the log was picked up in the woods, it too was transported in the same cart that was way to short for walking the distance we had to walk.
u/SituationNecessary15 — 21 hours ago
▲ 5 r/SCX24
Some shots of the crawler course I built
The course has really helped me with throttle control. I did realize that my truck doesn’t have the greatest steering angle so I decided to add 4WS. Which I’m really pumped for.
u/SituationNecessary15 — 20 hours ago
▲ 2 r/SCX24
Help with axle gearing for custom 6x6 scx24
Hey all, I am (and have been for quite some time now) working on a custom 6x6 build that started out as a deadbolt. I designed and printed a chassis and everything, and pulled the trigger on some Meus iso front axles for 4ws on the front and rear axles.
The problem I'm having is OD gears that come stock with these axles. I have a pass-through 2/16 worm gear for my center axle, and Meus iso axles come with either 2/12 or 2/14 gears. I think what i need currently is a set of 2/16 or slightly lower gears that fit with the Meus front axles (they sell one for their rear axle, but that gear is skinnier than the iso front axles). So currently I'm sitting with 2/14, 2/16, and 2/14, rear, middle, and front, and would much prefer 2/16, 2/16, and 2/14 or similar.
Anybody know if there are other gears out there that fit the Meus iso front axles, or heck, even a 2/14 pass-through worm gear that fits a stock scx24 axle?
u/Azurhalo — 12 hours ago
Week