u/Tyche_Miner

Here is my “close” to finalized design for the NerdOctAxe “Super Cool Stand” echo echo (trademarked!! but not really). I am designing this because I haven’t been able to find anything cool like this anywhere online that could be used to replace some not so good stands either to purcahse or even buy. Once I am fully done with design and I have at least one printed and tested stand that is functional. I will be posting the “FREE” STL on my home page. The only thing I ask from you is to follow me on Reddit. I will be adding all my custom, functional, and quirky Designs by TycheMiner here and on my page as well as on MakersWorld and Printables (which i will be setting up soon). I have so far about 20 different designs for different things from miners to soldering holders and stands.  I offer this my latest design to my fellow MINERS and my design(s) is NOT FOR RESELLERS! Helium Deploy talking to you taking things off makersworld and marking them up for resale! Thats horrible and bugs me!

This is not only a little teaser of the stand but it is also to ask you guys out there mining these if I should add anything else to make this better for all of us. Here are the characteristics: Maximizing air flow and circulation keeping sides free from obstruction/blockages. The back of the stand will hold two 90mm fans for best overall rear cooling. (I did try placing a single 200mm fan in the rear but it was not practical or did not cool anywhere near the twin 90mm fans do. that being said I will be also designing a stand for twin 120mm fasn that angle in towrds the middle sp they not only fit but casue a nice whirling effect of air cooling everything near them) Ok so, RPM rules in this game of cooling for max OC. The front design has a added rest shelf along th entire front bottom to help distribute the weight off the screw holes so that any mods could added to the pcb without worry of breaking board or holes. and finally the rear panel is an extra 3mm thick to add for more strength and stability of the stand. The one thing I am thinking of adding is down the center of the front panel that holdsthe PCB but facing the fans is a small 10mm or so dual sided (for lasck of a better words) “air ramp” pushing air out to either side. But before I do that I will finish this design and post the STL for my fellow miners to use. My designs are NOT FOR RESELLERS to use. This is a FREE design (NOT FOR VENDORS OR RESALE) and should not be charged for. 

Here is my “close” to finalized design for the NerdOctAxe “Super Cool Stand” echo echo (trademarked!! but not really). I am designing this because I haven’t been able to find anything cool like this anywhere online that could be used to replace some not so good stands either to purcahse or even buy. Once I am fully done with design and I have at least one printed and tested stand that is functional. I will be posting the “FREE” STL on my home page. The only thing I ask from you is to follow me on Reddit. I will be adding all my custom, functional, and quirky Designs by TycheMiner here and on my page as well as on MakersWorld and Printables (which i will be setting up soon). I have so far about 20 different designs for different things from miners to soldering holders and stands.  I offer this my latest design to my fellow MINERS and my design(s) is NOT FOR RESELLERS! Helium Deploy talking to you taking things off makersworld and marking them up for resale! Thats horrible and bugs me!

This is not only a little teaser of the stand but it is also to ask you guys out there mining these if I should add anything else to make this better for all of us. Here are the characteristics: Maximizing air flow and circulation keeping sides free from obstruction/blockages. The back of the stand will hold two 90mm fans for best overall rear cooling. (I did try placing a single 200mm fan in the rear but it was not practical or did not cool anywhere near the twin 90mm fans do. that being said I will be also designing a stand for twin 120mm fasn that angle in towrds the middle sp they not only fit but casue a nice whirling effect of air cooling everything near them) Ok so, RPM rules in this game of cooling for max OC. The front design has a added rest shelf along th entire front bottom to help distribute the weight off the screw holes so that any mods could added to the pcb without worry of breaking board or holes. and finally the rear panel is an extra 3mm thick to add for more strength and stability of the stand. The one thing I am thinking of adding is down the center of the front panel that holdsthe PCB but facing the fans is a small 10mm or so dual sided (for lasck of a better words) “air ramp” pushing air out to either side. But before I do that I will finish this design and post the STL for my fellow miners to use. My designs are NOT FOR RESELLERS to use. This is a FREE design (NOT FOR VENDORS OR RESALE) and should not be charged for.